Contact Us Home Home

UV Probes

FeaturesProbes

Analogue probes available with different housings for a wide range of industrial applications.

Probes can be configured for UV broadband, UVA, UVB, UVC, Erythema or blue light measurement (spectral sensitivity)

Software based calibration, integrated microcontroller.

Have a look at our UV-Sensor Probes Catalogue or scroll down for simple product selection.

 

 

 

Probes can be configured with different signal outputs (0...5 V; 4...20 mA; USB or Output for flash measurements) for different intensity ranges and with a 2 m shielded cable, with a male 5 pin plug or to be submersible.

When ordering or enquiring about these products please indicate: application, mechanical design (housing), spectral sensitivity (UV broadband, UVA, UVB, UVC, Erythema or blue light), signal output required, intensity range or maximum intensity and connector.

UV Probes - mechanical housing

UV_Air

Standard axis oriented in-chamber UV sensor.

UV_Surface

Standard surface-mount 180° FOV UV sensor.

UV_Water

10 bar water pressure proof UV sensor for low pressure lamps

UV_Water G3/4"

10 bar water pressure proof UV sensor with G 3/4" thread for medium and low pressure lamps.

UV_Cosine

Waterproof UV sensor for outdoor use.

UV_Cure

Sensor for hard UV irradiation with integrated temperature sensor.

It can be used permanently up to 170°C

UV_DVGW

UV Sensor for DVGW certified water purifiers. Minimum order quantity 15 pieces.

UV_DVGW_160

UV Sensor for DVGW (160°) and OE-Norm certified water purifiers. Minimum order quantity 15 pieces.

TOCON_Probe

Pre-amplified UV Photodetector with housing.

UV Probes - spectral sensitivity

When ordering please select a spectral sensitivity from the following list:

UV Broadband

Configure the sensor with a UV broadband SiC detector.

UVA

Configure the sensor with a UVA-only SiC detector.

UVB/UV-Index

Configure the sensor with a UVB-only/UV-Index SiC detector.

UVC

Configure the sensor with a UVC-only SiC detector.

UV Probes - signal output

When ordering please indicate the signal output required. Chose one from the following list:

0...5 V

Sensor will be configured with a 0...5 V signal output.

4...20 mA

Sensor will be configured with a 4...20 mA signal output.

USB

Sensor will be configured with a USB signal output.

Output for flash measurements

Sensor will be configured with an adjustable level output for flash measurements.

UV Probes - intensity range

When ordering please indicate one of the following intensity ranges:

1 nW/cm²...10 µW/cm²

Sensor will be configured for low intensities from 1 nW/cm²...10 µW/cm².

10 µW/cm²...100 mW/cm²

Sensor will be configured for medium intensities from 10 µW/cm²...100 mW/cm².

100 mW/cm²...10 W/cm²

Sensor will be configured for high intensities from 100 mW/cm²...10 W/cm².

If you are not sure which range will be convenient for you please let us know the application and/or model of the UV lamp you are using.

UV Probes - connector

When ordering please indicate one of the following connectors:

Cable

Sensor will be configured with a 2 m shielded cable.

Plug

Sensor will be configured with a male 5 pin plug; a 2 m cable is provided

Submersible

Sensor will be configured to be submersible

 

 

Accessories

Measurement Window WIN294

Measurement window for certified UV sensors according to DVGW 294-3 and ÖNORM M5873 Minimum order quantity 15 pieces.

 

Temperature sensor

PT100 sensor integrated into the probe housing

Monitors

Sensor monitor 5.0 series

 

Please consider our UV monitor and UV controller offer.

Ordering Information

Please contact us for more information.

Home | Products | Newsletter | Representatives | Contact | Website Policies
Scitec Instruments Ltd 1999 - 2009. All rights reserved.